Added storage/charging station
renamed 10.04 gerber zip
Merge branch 'master' of ssh://roboclub.org/home/svn/scouthw
fixed extra inner layer problem with set used-layers
re-ran CAM with dimension layer
added dimensions file
using 11 mil clearance, added latest gerber zip
added gerbers as of october 3, 2010. dfm check in progress.
Increased trace width on VCC and ACC_5V lines
Changed trace angles to 45deg and moved vias from silkscreen
Added SmartFly directory and component specs for ATtiny261
Added website silk and moved vias away from silk labels
Rerouted traces for aesthetics
Revised to pass DRC, added top ground plane and connecting vias
Changed power traces to 16mil, refined layout
Changed trace width to 8mil as per BatchPCB DRC, changed stepper to RA ZH JST6
updated scoutfly with new jst parts
updated silk on jst parts
Merge branch 'master' of roboclub8.frc.ri.cmu.edu:/home/svn/scouthw
All components routed, first pass. Needs cleaned up and final silk added
updated gitignore for temp library files
added JST_6 VERT part
Started routing, all but sonar and stepper.
swapped jst-5 headers from right angle to vertical
Added .gitignore file to ignore Eagle temp files
Added silk and mounting holes
Roboclub logo library
Added 5x2 accessory header and placed components
Added board perimeter, consolidated power connectors
Revised header placement on breafkly for more efficent routing
Renamed board to breakfly.sch
Added breakfly diagram
initial commit jst-based breakfly board
Renamed (molex cgrid) Breakfly schematic to breakfly_old. Starting new version using JST connectors.
updated kwoo.lbr with vertical package to jst_5
changed accessory pin names and moved one to sonar.
redid traces for front screw holes to avoid antenna. moved battery silk down.
4 Layer, 6mil trace/width, 15mil drill minimum drc file
added grounded srew holes to scoutfly. for review by kwoo.
Latest version of the library containing most of the scout parts
changed the value on the accessory detect pin resistor divider to a standard value
added silk, fixed layout bugs
Added some more ground planes on the unused bottom layer
Layout completed. Need to fix silk
Signal routing completed, power still needs to be done.
Finished layout for steppers and battery/charging contact support circuitry
Floorplan for the new stepper controller
Replaced stepper controller with one that will work for our voltages, fixes to the AVR on the clock and decoupling caps
AVR and BOM layout completed.
Gumstix layout mostly complete, AVR layout started. Some additional notes around the stepper driver on configuration, changes to the SPI header
Removed USB power since it would not work, simplified power area, reordered pins on the level shifters for easier layout.
Removed extraneous pullups from stepper controller
Fixed some pull up/down bugs
Started layout on scoutfly, updated schematic to use gumstix
Copied old atmel version of the scoutfly to the current version
Backed up the scoutfly atmel version in the repo
These are the CAM jobs and the design rules used
minor fixes
fixed some vias and traces, ready for CAM
Completed flyswatter schematic.
moved bom to bomboard/bomfly, added silk
Added flyswatter schematic. Almost done.
Added 2,3,4 pin JST headers, fixed the RA 5 pin JST header
Added the new breakfly schematic.
finished diode traces, made board smaller (2x1 in exact)
about to add diodes for voltage drop before emitters
changed emitter resistors to 1206, redid traces
fixed ERC errors
added datasheets and new jst version of bom board
Current version of the scout library
Removed symlink to the library since that wasn't working
Version 1.0 of the scoutfly. These are the zipped gerbers. Sent to the board/stencil houses
Fixed issues with non-standard resistor values
Fixed error in smybol for the Power OR controllers where the FET's drain only had 1 out of 6 connections. Finished redoing the floorplan on the Power OR section. Routing done for the top and bottom layers. Only need to do the power plane level now.
fixed some bom layout stuff
Routed some power planes. Started on the power OR controllers but need to redo floorplan.
Added SPI lines to the wireless chip and the control lines. Replaced standoff terminals with the Sparkfun parts which have better keepouts for the screwheads.
Routed all signal wires out of the ARM. Still need to do final connections. Moved flash jumpers and debug port around to facilitate routing
updates scout BOM schematic and board. i finished routing, but needs to be checked.
Finished routing PSU, user buttons, fixed a bug in tolerances in the wireless chip.
Reorganized the I2C pins on the FFC. Routed I2C and the I2C levelshifter. Finished the PSU poly pours except for the VCC pour. The Motor current limiters are laid out except for the VCC connection. Hooked up the wireless chips except SPI. Added a mounting hole for the BOM board.
adding scout bom board to repo
Some PSU routing, WL chip except external signals is done. Fixed resistor size (package) for the MAX745 battery charger
ORB and button wiring, some UART stuff.
Routed AVR, motor drivers, JTAG, USB ports, debug UART and some of the decoupling caps across the board.