Colony

#include <avr/io.h>

int main (void)

{

	/*

	TCCR1 is the timer counter compare register. 3 bits full of different settings you can change.

	We only cared about options in the first two bits.

	*/

   //Timer Counter Compare Register 1

   TCCR1A = 0b11000011;

   //Timer Counter Compare Register 1

   TCCR1B = 0b00001001;

   //TCCR1C = 0b10000000;

   /*data direction register for d. Used to change between read and write.*/

   DDRD = 0b00100000;

   /*

   output compare register

   the output is high when the counter counts higher than this

   the higher the number, the lower the duty cycle

   note: this is a 10 bit counter so changing the left six won't do anything

   */

   OCR1A = 0b0000001000000000;

   //i tried to enable output compare A match interrupts; apparently this is useless

   //TIMSK1 = 0b00000010;

   while (1)

   {

   }

}

# Hey Emacs, this is a -*- makefile -*-

#----------------------------------------------------------------------------

# WinAVR Makefile Template written by Eric B. Weddington, J?rg Wunsch, et al.

#

# Released to the Public Domain

#

# Additional material for this makefile was written by:

# Peter Fleury

# Tim Henigan

# Colin O'Flynn

# Reiner Patommel

# Markus Pfaff

# Sander Pool

# Frederik Rouleau

#

#----------------------------------------------------------------------------

# On command line:

#

# make all = Make software.

#

# make clean = Clean out built project files.

#

# make coff = Convert ELF to AVR COFF.

#

# make extcoff = Convert ELF to AVR Extended COFF.

#

# make program = Download the hex file to the device, using avrdude.

#                Please customize the avrdude settings below first!

#

# make debug = Start either simulavr or avarice as specified for debugging, 

#              with avr-gdb or avr-insight as the front end for debugging.

#

# make filename.s = Just compile filename.c into the assembler code only.

#

# make filename.i = Create a preprocessed source file for use in submitting

#                   bug reports to the GCC project.

#

# To rebuild project do "make clean" then "make all".

#----------------------------------------------------------------------------

# MCU name

MCU = atmega164p

# Processor frequency.

#     This will define a symbol, F_CPU, in all source code files equal to the 

#     processor frequency. You can then use this symbol in your source code to 

#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done

#     automatically to create a 32-bit value in your source code.

F_CPU = 5000000

# Output format. (can be srec, ihex, binary)

FORMAT = ihex

# Target file name (without extension).

TARGET = timerBlink

# List C source files here. (C dependencies are automatically generated.)

SRC = $(TARGET).c

# List Assembler source files here.

#     Make them always end in a capital .S.  Files ending in a lowercase .s

#     will not be considered source files but generated files (assembler

#     output from the compiler), and will be deleted upon "make clean"!

#     Even though the DOS/Win* filesystem matches both .s and .S the same,

#     it will preserve the spelling of the filenames, and gcc itself does

#     care about how the name is spelled on its command-line.

ASRC = 

# Optimization level, can be [0, 1, 2, 3, s]. 

#     0 = turn off optimization. s = optimize for size.

#     (Note: 3 is not always the best optimization level. See avr-libc FAQ.)

OPT = s

# Debugging format.

#     Native formats for AVR-GCC's -g are dwarf-2 [default] or stabs.

#     AVR Studio 4.10 requires dwarf-2.

#     AVR [Extended] COFF format requires stabs, plus an avr-objcopy run.

DEBUG = dwarf-2

# List any extra directories to look for include files here.

#     Each directory must be seperated by a space.

#     Use forward slashes for directory separators.

#     For a directory that has spaces, enclose it in quotes.

#EXTRAINCDIRS = C:\WinAVR\include\fwr

# Compiler flag to set the C Standard level.

#     c89   = "ANSI" C

#     gnu89 = c89 plus GCC extensions

#     c99   = ISO C99 standard (not yet fully implemented)

#     gnu99 = c99 plus GCC extensions

CSTANDARD = -std=gnu99

# Place -D or -U options here

CDEFS = -DF_CPU=$(F_CPU)UL

# Place -I options here

CINCS =

#---------------- Compiler Options ----------------

#  -g*:          generate debugging information

#  -O*:          optimization level

#  -f...:        tuning, see GCC manual and avr-libc documentation

#  -Wall...:     warning level

#  -Wa,...:      tell GCC to pass this to the assembler.

#    -adhlns...: create assembler listing

CFLAGS = -g$(DEBUG)

CFLAGS += $(CDEFS) $(CINCS)

CFLAGS += -O$(OPT)

CFLAGS += -funsigned-char -funsigned-bitfields -fpack-struct -fshort-enums

CFLAGS += -Wall -Wstrict-prototypes

CFLAGS += -Wa,-adhlns=$(<:.c=.lst)

CFLAGS += $(patsubst %,-I%,$(EXTRAINCDIRS))

CFLAGS += $(CSTANDARD)

#---------------- Assembler Options ----------------

#  -Wa,...:   tell GCC to pass this to the assembler.

#  -ahlms:    create listing

#  -gstabs:   have the assembler create line number information; note that

#             for use in COFF files, additional information about filenames

#             and function names needs to be present in the assembler source

#             files -- see avr-libc docs [FIXME: not yet described there]

ASFLAGS = -Wa,-adhlns=$(<:.S=.lst),-gstabs 

#---------------- Library Options ----------------

# Minimalistic printf version

PRINTF_LIB_MIN = -Wl,-u,vfprintf -lprintf_min

# Floating point printf version (requires MATH_LIB = -lm below)

PRINTF_LIB_FLOAT = -Wl,-u,vfprintf -lprintf_flt

# If this is left blank, then it will use the Standard printf version.

PRINTF_LIB = 

#PRINTF_LIB = $(PRINTF_LIB_MIN)

#PRINTF_LIB = $(PRINTF_LIB_FLOAT)

# Minimalistic scanf version

SCANF_LIB_MIN = -Wl,-u,vfscanf -lscanf_min

# Floating point + %[ scanf version (requires MATH_LIB = -lm below)

SCANF_LIB_FLOAT = -Wl,-u,vfscanf -lscanf_flt

# If this is left blank, then it will use the Standard scanf version.

SCANF_LIB = 

#SCANF_LIB = $(SCANF_LIB_MIN)

#SCANF_LIB = $(SCANF_LIB_FLOAT)

MATH_LIB = -lm

#---------------- External Memory Options ----------------

# 64 KB of external RAM, starting after internal RAM (ATmega128!),

# used for variables (.data/.bss) and heap (malloc()).

#EXTMEMOPTS = -Wl,-Tdata=0x801100,--defsym=__heap_end=0x80ffff

# 64 KB of external RAM, starting after internal RAM (ATmega128!),

# only used for heap (malloc()).

#EXTMEMOPTS = -Wl,--defsym=__heap_start=0x801100,--defsym=__heap_end=0x80ffff

EXTMEMOPTS =

#---------------- Linker Options ----------------

#  -Wl,...:     tell GCC to pass this to linker.

#    -Map:      create map file

#    --cref:    add cross reference to  map file

LDFLAGS = -Wl,-Map=$(TARGET).map,--cref

LDFLAGS += $(EXTMEMOPTS)

LDFLAGS += $(PRINTF_LIB) $(SCANF_LIB) $(MATH_LIB)

#---------------- Programming Options (avrdude) ----------------

# Programming hardware: alf avr910 avrisp bascom bsd 

# dt006 pavr picoweb pony-stk200 sp12 stk200 stk500

#

# Type: avrdude -c ?

# to get a full listing.

#

AVRDUDE_PROGRAMMER = avrisp

# com1 = serial port. Use lpt1 to connect to parallel port.

AVRDUDE_PORT = com1

# programmer connected to serial device

AVRDUDE_WRITE_FLASH = -b 4800 -U flash:w:$(TARGET).hex

#AVRDUDE_WRITE_EEPROM = -U eeprom:w:$(TARGET).eep

# Uncomment the following if you want avrdude's erase cycle counter.

# Note that this counter needs to be initialized first using -Yn,

# see avrdude manual.

#AVRDUDE_ERASE_COUNTER = -y

# Uncomment the following if you do /not/ wish a verification to be

# performed after programming the device.

#AVRDUDE_NO_VERIFY = -V

# Increase verbosity level.  Please use this when submitting bug

# reports about avrdude. See <http://savannah.nongnu.org/projects/avrdude> 

# to submit bug reports.

#AVRDUDE_VERBOSE = -v -v

AVRDUDE_FLAGS = -p $(MCU) -P $(AVRDUDE_PORT) -c $(AVRDUDE_PROGRAMMER)

AVRDUDE_FLAGS += $(AVRDUDE_NO_VERIFY)

AVRDUDE_FLAGS += $(AVRDUDE_VERBOSE)

AVRDUDE_FLAGS += $(AVRDUDE_ERASE_COUNTER)

#---------------- Debugging Options ----------------

# For simulavr only - target MCU frequency.

DEBUG_MFREQ = $(F_CPU)

# Set the DEBUG_UI to either gdb or insight.

# DEBUG_UI = gdb

DEBUG_UI = insight

# Set the debugging back-end to either avarice, simulavr.

DEBUG_BACKEND = avarice

#DEBUG_BACKEND = simulavr

# GDB Init Filename.

GDBINIT_FILE = __avr_gdbinit

# When using avarice settings for the JTAG

JTAG_DEV = /dev/com1

# Debugging port used to communicate between GDB / avarice / simulavr.

DEBUG_PORT = 4242

# Debugging host used to communicate between GDB / avarice / simulavr, normally

#     just set to localhost unless doing some sort of crazy debugging when 

#     avarice is running on a different computer.

DEBUG_HOST = localhost

#============================================================================

# Define programs and commands.

SHELL = sh

CC = avr-gcc

OBJCOPY = avr-objcopy

OBJDUMP = avr-objdump

SIZE = avr-size

NM = avr-nm

AVRDUDE = avrdude

REMOVE = rm -f

COPY = cp

WINSHELL = cmd

# Define Messages

# English

MSG_ERRORS_NONE = Errors: none

MSG_BEGIN = -------- begin --------

MSG_END = --------  end  --------

MSG_SIZE_BEFORE = Size before: 

MSG_SIZE_AFTER = Size after:

MSG_COFF = Converting to AVR COFF:

MSG_EXTENDED_COFF = Converting to AVR Extended COFF:

MSG_FLASH = Creating load file for Flash:

MSG_EEPROM = Creating load file for EEPROM:

MSG_EXTENDED_LISTING = Creating Extended Listing:

MSG_SYMBOL_TABLE = Creating Symbol Table:

MSG_LINKING = Linking:

MSG_COMPILING = Compiling:

MSG_ASSEMBLING = Assembling:

MSG_CLEANING = Cleaning project:

# Define all object files.

OBJ = $(SRC:.c=.o) $(ASRC:.S=.o) 

# Define all listing files.

LST = $(SRC:.c=.lst) $(ASRC:.S=.lst) 

# Compiler flags to generate dependency files.

GENDEPFLAGS = -MD -MP -MF .dep/$(@F).d

# Combine all necessary flags and optional flags.

# Add target processor to flags.

ALL_CFLAGS = -mmcu=$(MCU) -I. $(CFLAGS) $(GENDEPFLAGS)

ALL_ASFLAGS = -mmcu=$(MCU) -I. -x assembler-with-cpp $(ASFLAGS)

# Default target.

all: begin gccversion sizebefore build sizeafter end

build: elf hex eep lss sym

elf: $(TARGET).elf

hex: $(TARGET).hex

eep: $(TARGET).eep

lss: $(TARGET).lss 

sym: $(TARGET).sym

# Eye candy.

# AVR Studio 3.x does not check make's exit code but relies on

# the following magic strings to be generated by the compile job.

begin:

	@echo

	@echo $(MSG_BEGIN)

end:

	@echo $(MSG_END)

	@echo

# Display size of file.

HEXSIZE = $(SIZE) --target=$(FORMAT) $(TARGET).hex

ELFSIZE = $(SIZE) -A $(TARGET).elf

AVRMEM = avr-mem.sh $(TARGET).elf $(MCU)

sizebefore:

	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_BEFORE); $(ELFSIZE); \

	$(AVRMEM) 2>/dev/null; echo; fi

sizeafter:

	@if test -f $(TARGET).elf; then echo; echo $(MSG_SIZE_AFTER); $(ELFSIZE); \

	$(AVRMEM) 2>/dev/null; echo; fi

# Display compiler version information.

gccversion : 

	@$(CC) --version

# Program the device.  

program: $(TARGET).hex $(TARGET).eep

	$(AVRDUDE) $(AVRDUDE_FLAGS) $(AVRDUDE_WRITE_FLASH) $(AVRDUDE_WRITE_EEPROM)

# Generate avr-gdb config/init file which does the following:

#     define the reset signal, load the target file, connect to target, and set 

#     a breakpoint at main().

gdb-config: 

	@$(REMOVE) $(GDBINIT_FILE)

	@echo define reset >> $(GDBINIT_FILE)

	@echo SIGNAL SIGHUP >> $(GDBINIT_FILE)

	@echo end >> $(GDBINIT_FILE)

	@echo file $(TARGET).elf >> $(GDBINIT_FILE)

	@echo target remote $(DEBUG_HOST):$(DEBUG_PORT)  >> $(GDBINIT_FILE)

ifeq ($(DEBUG_BACKEND),simulavr)

	@echo load  >> $(GDBINIT_FILE)

endif	

	@echo break main >> $(GDBINIT_FILE)

debug: gdb-config $(TARGET).elf

ifeq ($(DEBUG_BACKEND), avarice)

	@echo Starting AVaRICE - Press enter when "waiting to connect" message displays.

	@$(WINSHELL) /c start avarice --jtag $(JTAG_DEV) --erase --program --file \

	$(TARGET).elf $(DEBUG_HOST):$(DEBUG_PORT)

	@$(WINSHELL) /c pause

else

	@$(WINSHELL) /c start simulavr --gdbserver --device $(MCU) --clock-freq \

	$(DEBUG_MFREQ) --port $(DEBUG_PORT)

endif

	@$(WINSHELL) /c start avr-$(DEBUG_UI) --command=$(GDBINIT_FILE)

# Convert ELF to COFF for use in debugging / simulating in AVR Studio or VMLAB.

COFFCONVERT=$(OBJCOPY) --debugging \

--change-section-address .data-0x800000 \

--change-section-address .bss-0x800000 \

--change-section-address .noinit-0x800000 \

--change-section-address .eeprom-0x810000 

coff: $(TARGET).elf

	@echo

	@echo $(MSG_COFF) $(TARGET).cof

	$(COFFCONVERT) -O coff-avr $< $(TARGET).cof

extcoff: $(TARGET).elf

	@echo

	@echo $(MSG_EXTENDED_COFF) $(TARGET).cof

	$(COFFCONVERT) -O coff-ext-avr $< $(TARGET).cof

# Create final output files (.hex, .eep) from ELF output file.

%.hex: %.elf

	@echo

	@echo $(MSG_FLASH) $@

	$(OBJCOPY) -O $(FORMAT) -R .eeprom $< $@

%.eep: %.elf

	@echo

	@echo $(MSG_EEPROM) $@

	-$(OBJCOPY) -j .eeprom --set-section-flags=.eeprom="alloc,load" \

	--change-section-lma .eeprom=0 -O $(FORMAT) $< $@

# Create extended listing file from ELF output file.

%.lss: %.elf

	@echo

	@echo $(MSG_EXTENDED_LISTING) $@

	$(OBJDUMP) -h -S $< > $@

# Create a symbol table from ELF output file.

%.sym: %.elf

	@echo

	@echo $(MSG_SYMBOL_TABLE) $@

	$(NM) -n $< > $@

# Link: create ELF output file from object files.

.SECONDARY : $(TARGET).elf

.PRECIOUS : $(OBJ)

%.elf: $(OBJ)

	@echo

	@echo $(MSG_LINKING) $@

	$(CC) $(ALL_CFLAGS) $^ --output $@ $(LDFLAGS)

# Compile: create object files from C source files.

%.o : %.c

	@echo

	@echo $(MSG_COMPILING) $<

	$(CC) -c $(ALL_CFLAGS) $< -o $@ 

# Compile: create assembler files from C source files.

%.s : %.c

	$(CC) -S $(ALL_CFLAGS) $< -o $@

# Assemble: create object files from assembler source files.

%.o : %.S

	@echo

	@echo $(MSG_ASSEMBLING) $<

	$(CC) -c $(ALL_ASFLAGS) $< -o $@

# Create preprocessed source for use in sending a bug report.

%.i : %.c

	$(CC) -E -mmcu=$(MCU) -I. $(CFLAGS) $< -o $@ 

# Target: clean project.

clean: begin clean_list end

clean_list :

	@echo

	@echo $(MSG_CLEANING)

	$(REMOVE) $(TARGET).hex

	$(REMOVE) $(TARGET).eep

	$(REMOVE) $(TARGET).cof

	$(REMOVE) $(TARGET).elf

	$(REMOVE) $(TARGET).map

	$(REMOVE) $(TARGET).sym

	$(REMOVE) $(TARGET).lss

	$(REMOVE) $(OBJ)

	$(REMOVE) $(LST)

	$(REMOVE) $(SRC:.c=.s)

	$(REMOVE) $(SRC:.c=.d)

	$(REMOVE) .dep/*

# Include the dependency files.

-include $(shell mkdir .dep 2>/dev/null) $(wildcard .dep/*)

# Listing of phony targets.

.PHONY : all begin finish end sizebefore sizeafter gccversion \

build elf hex eep lss sym coff extcoff \

clean clean_list program debug gdb-config