Statistics
| Branch: | Revision:

root / scoutfly / scoutfly.brd @ 15a40e6f

History | View | Annotate | Download (227 KB)

# Date Author Comment
1a5559b0 11/05/2011 10:46 pm Abraham Levkoy

Changed USB port drill holes back to spec

Looked at mini USB port with Dan. Observed that corner drill holes are
supposed to be multiple drills right next to eachother. Decided to
change holes back to specfied radius and ignore long hole for now.

33c4366f 11/04/2011 06:10 pm Abraham Levkoy

Updated DS2786 footprint in kwoo library

Updated package footprint for DS2786 in kwoo.lbr based on recommended
land placement in datasheet for DFN10 package. DS2786's datasheet lists
TDFN10 as its package type but doesn't give placement guidance or a
useful package description. Unable to find a datasheet for TDFN10, but...

51b65a87 11/04/2011 05:09 pm Abraham Levkoy

Increased mini-USB plug drill hole size

Imported MINI-USB- device from Hirose Connectors library into kwoo
library. In UX60-MB-5S8 package, increased drill hole size on corner
pins from .8 mm to .9 mm. I did not drill out the original too-small
holes on Scoutfly, so I don't know whether this is sufficient or not....

5a7bbf4c 10/26/2011 09:10 pm Yuyang Guo

fixing last 13 angle problem in drc

don't really know how to fix the last one.
worked on right bottom on both top layer and bottom layer

a433b5ff 10/23/2011 10:19 am Yuyang Guo

solving some angle problems on scoutflu board

cf5c3070 10/22/2011 05:32 pm Thomas Mullins

Fixed some of the paths which are at unusual angles

ca0c1be9 10/22/2011 05:03 pm Yuyang Guo

fixing some of the angle problems in scoutfly.sch

b68f4fd7 09/29/2011 10:13 pm Abraham Levkoy

Finished hooking up new gyroscope.

Connected pitch output of gyroscope to AVR and gave pitch an output LPF.
Added optional HPFs to both pitch and yaw outputs. We can just leave the
pads empty if we think they won't be useful.

To route the changes, had to squeeze some other stuff. Moved the AVR...

0075932e 09/17/2011 04:39 am Abraham Levkoy

Routed new gyroscope.

Routed new gyroscope on board in Eagle.

64958645 09/17/2011 03:53 am Abraham Levkoy

Swapped gyroscope part in schematic.

Replaced old gyroscope part with new one in schematic. Assuming that
pitch output or amplified outputs are undesired. Not using optional
high-pass filter on output. Have not yet routed connections to gyroscope
on board.

5dbaecb0 09/13/2011 11:06 pm Abraham Levkoy

Flipped FFC connector on PCB.

Flipped FFC connector (part J3) on Scoutfly so that mating side faces
out from edge of board. Rerouted wires connecting to J3 to accomodate
this. Because the connected ports don't line up as well as they used to,
the area below J3 has a lot of roundabout paths and layer switches. I...

d374c1a4 08/15/2011 01:56 am Abraham Levkoy

Began fixing bugs for Scoutfly fixup.

Made several of the changes listed on wiki page ScoutflyUpdate2011. In
particular:
Removed R4 and connected pin 4 on U$3 directly to VCC.
Connected VREG_EN to VCC with 10 kOhm resistor (new R4).
Changed value of R26 to 100 kOhms....

79365002 01/17/2011 11:16 pm Christopher Mar

updated silkscreen with new version and date

68814b9c 01/17/2011 11:06 pm Christopher Mar

updated scoutfly and kwoo lbr with dual NPN

5edd4248 10/12/2010 09:58 pm Chris Mar

fixed extra inner layer problem with set used-layers

0b6ae624 10/04/2010 03:35 pm Chris Mar

using 11 mil clearance, added latest gerber zip

f81c1cf2 10/02/2010 05:14 am Chris Mar

updated scoutfly with new jst parts

8881541a 10/02/2010 12:37 am Chris Mar

swapped jst-5 headers from right angle to vertical

f98422cf 09/29/2010 04:15 pm Chris Mar

changed accessory pin names and moved one to sonar.

f7a00d18 09/26/2010 07:38 pm Chris Mar

redid traces for front screw holes to avoid antenna. moved battery silk down.

0128ce26 09/26/2010 04:28 pm Chris Mar

added grounded srew holes to scoutfly. for review by kwoo.

561596fa 08/14/2010 03:39 am Kevin Woo

changed the value on the accessory detect pin resistor divider to a standard value

14ab72d8 08/14/2010 03:31 am Kevin Woo

added silk, fixed layout bugs

f397fa03 08/14/2010 02:19 am Kevin Woo

Added some more ground planes on the unused bottom layer

3f08631a 08/14/2010 02:01 am Kevin Woo

Layout completed. Need to fix silk

372d40a6 08/02/2010 12:50 am Kevin Woo

Signal routing completed, power still needs to be done.

ad4c386a 08/01/2010 10:00 pm Kevin Woo

Finished layout for steppers and battery/charging contact support circuitry

b27f70a5 07/30/2010 11:00 am Kevin Woo

Floorplan for the new stepper controller

266d88f8 07/30/2010 12:55 am Kevin Woo

Replaced stepper controller with one that will work for our voltages, fixes to the AVR on the clock and decoupling caps

305fe76c 07/28/2010 12:21 am Kevin Woo

AVR and BOM layout completed.

d326a8bd 07/26/2010 12:09 pm Kevin Woo

Gumstix layout mostly complete, AVR layout started. Some additional notes around the stepper driver on configuration, changes to the SPI header

fe1fe494 07/23/2010 09:32 pm Kevin Woo

Removed USB power since it would not work, simplified power area, reordered pins on the level shifters for easier layout.

75ded4fb 07/22/2010 06:07 pm Kevin Woo

Removed extraneous pullups from stepper controller

7e65c00d 07/22/2010 05:59 pm Kevin Woo

Fixed some pull up/down bugs

cffb0116 07/22/2010 12:09 am Kevin Woo

Started layout on scoutfly, updated schematic to use gumstix

1652a76c 05/01/2010 02:26 am Kevin Woo

Copied old atmel version of the scoutfly to the current version

95f0c096 05/01/2010 02:20 am Kevin Woo

Backed up the scoutfly atmel version in the repo

caddc018 02/07/2010 12:14 am Kevin Woo

Fixed issues with non-standard resistor values

4048af80 01/29/2010 09:21 pm Kevin Woo

Fixed error in smybol for the Power OR controllers where the FET's drain only had 1 out of 6 connections. Finished redoing the floorplan on the Power OR section. Routing done for the top and bottom layers. Only need to do the power plane level now.

7fd8a260 01/29/2010 04:21 pm Kevin Woo

Routed some power planes. Started on the power OR controllers but need to redo floorplan.

d4df41c7 01/29/2010 02:46 pm Kevin Woo

Added SPI lines to the wireless chip and the control lines. Replaced standoff terminals with the Sparkfun parts which have better keepouts for the screwheads.

5daf8060 01/29/2010 12:22 pm Kevin Woo

Routed all signal wires out of the ARM. Still need to do final connections. Moved flash jumpers and debug port around to facilitate routing

ca9f70ed 01/28/2010 11:43 pm Kevin Woo

Finished routing PSU, user buttons, fixed a bug in tolerances in the wireless chip.

b9c74451 01/28/2010 07:09 pm Kevin Woo

Reorganized the I2C pins on the FFC. Routed I2C and the I2C levelshifter. Finished the PSU poly pours except for the VCC pour. The Motor current limiters are laid out except for the VCC connection. Hooked up the wireless chips except SPI. Added a mounting hole for the BOM board.

a5862daf 01/28/2010 04:34 pm Kevin Woo

Some PSU routing, WL chip except external signals is done. Fixed resistor size (package) for the MAX745 battery charger

14570329 01/27/2010 10:58 pm Kevin Woo

ORB and button wiring, some UART stuff.

e91ddfc2 01/27/2010 03:06 am Kevin Woo

Routed AVR, motor drivers, JTAG, USB ports, debug UART and some of the decoupling caps across the board.

f9b43048 01/26/2010 07:43 pm Kevin Woo

Initial commit of the unfinished scout board and the current scout library