Project

General

Profile

Statistics
| Branch: | Revision:

scoutece / scoutfly @ 5a7bbf4c

Name Size
charging_test.sch 34.9 KB
scoutfly.brd 227 KB
scoutfly.dimensions.ger 8.85 KB
scoutfly.sch 361 KB
scoutfly_atmel.brd 274 KB
scoutfly_atmel.sch 396 KB
scoutfly_nxp.brd 150 KB
scoutfly_nxp.sch 366 KB
scoutfly_v1.0.zip 329 KB
scoutfly_v1.0_stencil.zip 11.7 KB
scoutfly_v1.1_10-03-2010.zip 252 KB
scoutfly_v1.1_10-04-2010.zip 252 KB
scoutfly_v1.1_10-08-2010.zip 222 KB

Latest revisions

# Date Author Comment
5a7bbf4c 10/26/2011 09:10 PM Yuyang Guo

fixing last 13 angle problem in drc

don't really know how to fix the last one.
worked on right bottom on both top layer and bottom layer
a433b5ff 10/23/2011 10:19 AM Yuyang Guo

solving some angle problems on scoutflu board
cf5c3070 10/22/2011 05:32 PM Thomas Mullins

Fixed some of the paths which are at unusual angles
ca0c1be9 10/22/2011 05:03 PM Yuyang Guo

fixing some of the angle problems in scoutfly.sch
6aece861 10/06/2011 05:28 PM Abraham Levkoy

Added kwoo's standalone charging schematic.

charging_test.sch is a standalone circuit schematic for a prototype to
test the charging circuit that will ultimately go on Scoutfly. kwoo
created it. It uses some new parts, but I don't know that much about it...
b68f4fd7 09/29/2011 10:13 PM Abraham Levkoy

Finished hooking up new gyroscope.

Connected pitch output of gyroscope to AVR and gave pitch an output LPF.
Added optional HPFs to both pitch and yaw outputs. We can just leave the
pads empty if we think they won't be useful.

To route the changes, had to squeeze some other stuff. Moved the AVR...
0075932e 09/17/2011 04:39 AM Abraham Levkoy

Routed new gyroscope.

Routed new gyroscope on board in Eagle.
64958645 09/17/2011 03:53 AM Abraham Levkoy

Swapped gyroscope part in schematic.

Replaced old gyroscope part with new one in schematic. Assuming that
pitch output or amplified outputs are undesired. Not using optional
high-pass filter on output. Have not yet routed connections to gyroscope
on board.
5dbaecb0 09/13/2011 11:06 PM Abraham Levkoy

Flipped FFC connector on PCB.

Flipped FFC connector (part J3) on Scoutfly so that mating side faces
out from edge of board. Rerouted wires connecting to J3 to accomodate
this. Because the connected ports don't line up as well as they used to,
the area below J3 has a lot of roundabout paths and layer switches. I...
d374c1a4 08/15/2011 01:56 AM Abraham Levkoy

Began fixing bugs for Scoutfly fixup.

Made several of the changes listed on wiki page ScoutflyUpdate2011. In
particular:
Removed R4 and connected pin 4 on U$3 directly to VCC.
Connected VREG_EN to VCC with 10 kOhm resistor (new R4).
Changed value of R26 to 100 kOhms....

View revisions

Also available in: Atom